|
|
|
|
|
Dynapar Brand Encoder
Series 60P Rotopulser
|
 |
|
(MOT) M061117
Danaher Controls Dynapar brand encoder.
Series 60P Rotopulser. Includes wiring and installation guide. Brand new in the
box!! Only one available.
Specifications:
• Slew speed: 3600 rpm
• Shaft diameter: 5/8"
• Inertia: 285 gm-cm2 max
• Typical Starting Torque: 15 oz-in
• Bearings: Motor Duty Bearings
• Weight: 10 lbs
• Shaft Loading: Radial: 45 lbs overhung; Axial: 15 lbs
• Operating Temp. Range: 0 to 54ºC
Electrical:
• Power Requirements: 5 to 15 vdc max
• Frequency Response: 50 kHz
|
|
|
Minebea / Astrosyn
Bipolar Stepper Motor |
 |
|
|
(MOT) 17PY-Q202-03
Minebea / Astrosyn bipolar stepper
motor. 5 volt, 0.4 amp, 12.5 ohms, 12.5 ohm coils. Shaft
diameter (4.992mm) 0.2"D x 0.4"L. 1-5/8" square x 7/8" high.
Four leads
(Y, R,
BK,
OR)
with
four-pin
socket
connector. 5,000 available!!
Minebea Astrosyn P/N: 17PY-Q202-03
• Full step angle: 0.9º =
400 steps
• Motor frame size: NEMA Size 17 (42mm)
• Holding Torque (oz/in) = Phase A - 10, Phase B - 10
• Inductance (mH): Phase A - 9, Phase B - 9
• Resistance (Ohms): Phase A - 12.4, Phase B - 12.6.
• Leakage: 500v
• Detent Torque (oz/in): 0.37.
Many uses: Engraving machine servo,
surveillance servo camera, robotics? |
|
|
|
| $19.95 each - $17.50 (10+), $15.95 (100+) |
|
|
|
|
|
Escap High Speed Step Motor
3.7 amps |
 |
|
(MOT) P532.258.0.7.69
Escap high speed stepping motor. Up to
9000 rpm. Made in Switzerland.
• 3.6 deg. 2-phase (8-wire)
• Rated Current: 3.7 amps
• DC Resistance: 0.34 ohms / phase (8 leads, 3.6 deg. step angle works with standard
bi-polar chopper drives.
• Holding torque: 33.4 oz.-in.
• Body dimensions: 52 mm square flange x 30 mm
• Shaft dimensions: 5 mm dia. x 20.5 mm L (flat)
|
|
|
Sigma Instruments
Unipolar Step Motor - 9.5 vdc |
 |
|
(MOT) 20-3424D-24244
Sigma Instruments unipolar step motor.
• (5 leads) 1.8 deg. / step; 300 steps / sec.; 3%
step accuracy.
• Rated Voltage: 9.5 vdc
• Rated Current: 0.5 amps
• Holding Torque: 60 oz. -in.
• Running Torque: 45 oz. -in.
• Body Dimensions: 3-3/8" dia. x 7/16"L, 3/8" square flange with 4 mounting holes.
• Shaft dimensions: 0.375" dia. x 1-1/8"L
|
|
| $29 each - $25 (5+), $20 (50+) |
| |
|
|
|
|
|
|
Stepping Motor
3.0 vdc / 4 amp |
 |
(MOT) HS50D-1001
Superior Electric Company stepping
motor. 200 step. 3.0 vdc, 4 amps. 85 oz. inches torque. Viscous damped, 2500
centistrokes. Includes circular connector for hookup
• Body Dimensions: 3-3/8" x 3-3/8" x 3-7/8"L
• Shaft Dimensions: 0.3750" dia. x 1-1/4"L
Motor can be operated as follows:
• Horizontal vent open
• Vertically up - vent closed
• Vertically down - vent open.
|
|
|
6 Wire Stepping Motor
60 Ohm / 3.75 Degrees
|
 |
(MOT) 42SH-32KCA
Six wire stepping motor. 60 ohm, 3.75 degrees. Made
in Japan.
• Body Dimensions: 1-11/16"
sq. x 1-5/16"H.
• Shaft Dimensions:
3/16" dia x 7/16"L flatted shaft.
|
|
| |
|
| $3.95 each - $3.40 (10+),
$3 (100+) |
| |
|
|
|
|
Stepper Motor
14 vdc |
 |
(MOT) 12-SPAM-22B/H050
Clifton Precision stepper motor. 30º, 14 vdc. 4 wire. 1-1/4" diameter body. 1/8" diameter spline shaft. |
|
|
Precision Servo Motor
6000 rpm |
 |
 |
(MOT) 1011-251-009
Beckman precision servo motor. 6000 rpm. 0.6 oz. in torque. 400 Hz frequency, 115v fixed, 40v control. 1.07" x 2.02" body. 1/8" x 3/8" fluted shaft. Top mount, 4 screws. |
|
|
|
|
Servo Motor
5 Wire / 1.8 Degree |
 |
| |
(MOT) V22747-M100-A6
Berger Lahr servo motor.
5 wire, 1.8 degree. 1-21/32" square x 1-1/4" high.
4.986 mm (0.196") dia. x 5/8" shaft. Made in Germany.
Manufacturer's model number: RDM253/50. |
|
|
DC Servo Motor
1800 rpm |
 |
|
(MOT) DS57B40-101
Japan Servo Company, Ltd. DC
Servo Motor. DC-44. 1800 rpm, 1.1 amp, 25 oz.-in. torque. 0.315" (8mm)
dia. x 1.25"L shaft. Includes timing belt pulley, 0.5" dia.
x 9/16" wide. Diablo printer P/N: 323863-01. |
|
| $15 each - $13 (5+),
$10 (50+) |
| |
|
|
|
|
|
|
Synchronous Stepping Motor
5.3 vdc / 1.6 amps |
 |
|
(MOT) M062-FD8103
Superior Electric "SLO-SYN" synchronous stepping motor. 5.3 vdc, 1.6 amps. 200 steps per revolution. Holding torque is 100 oz. in. 8 wire. 2-1/4"D x 3"L body. 1/4"D x 3/4" round shaft. |
|
|
|
|
|
